Wall removal is taking out an internal wall to open up rooms; where the wall is load-bearing, a steel beam sized by a structural engineer is installed on padstones to carry the weight above, with the work approved by building control.
Getting removing a wall right in Kempston starts with understanding the house you already have: its age, how it was built and what has been altered over the years. We survey first, then commit on paper to a price that holds as long as the scope stays the same. Across the East of England, guide prices run at £3,200–£8,400 including VAT, and homes in Bedford, Ampthill and Milton Keynes are covered too.
- Guide price
- £3,200–£8,400 inc VAT
- Time on site
- 1–3 weeks including making good
- Postcodes
- MK42
- Planning rules
- England
- Local area
- Bedford Borough
- Survey
- Free, with a written quote
How much does removing a wall cost in Kempston?
What will removing a wall cost in Kempston? Our guide range is £3,200–£8,400 including VAT. That figure is adjusted for the East of England, about 5% above the national guide, and is intended for planning a budget. A firm written price for your chosen specification follows a free survey at your home.
| Type of job | What it usually involves | Guide in Kempston |
|---|---|---|
| Non-load-bearing wall | Removing a stud or block partition and making good walls, ceiling and floor. | £850–£2,100 |
| Load-bearing wall up to 4m | A typical kitchen-diner knock-through with one steel beam, calculations and building control. | £3,200–£8,400 |
| Wide or complex opening | Openings over 4m, posts, flush beams or chimney breast removal. | £8,400–£17,000 |
The main things that change the figure:
- Opening width and the load the wall carries
- Beam size, posts, flush fixing and padstone details
- Services in the wall that need rerouting
- Engineer, building control and any party wall costs
Scope of the work
- Survey to establish what the wall supports and where loads go
- Structural engineer's calculations and beam specification
- Building control application and inspections
- Temporary propping and dust protection during the work
- Steel beam installed on padstones and packed tight
- Beam boarded or treated for fire protection
Building in Kempston
Bedfordshire has a long brick-making history, and brick dominates: Victorian terraces in Bedford and Luton, interwar semis, large post-war estates around Luton and Dunstable, and newer developments near Bedford and Biggleswade. Villages in the north of the county keep limestone cottages, with timber framing and thatch scattered across older settlements.
Bedfordshire is relatively dry, and its clay soils can shrink in long, dry summers, so foundation depth and nearby trees matter for extensions.
Whatever era your Kempston home dates from, we plan removing a wall around how it is actually built rather than a one-size-fits-all specification.
Planning and building rules in Kempston
As Kempston is in England, read the following with that system of planning and building control in mind. We check what applies to your house with the council before you receive a quote.
Removing an internal wall does not need planning permission in England unless the house is listed.
If the wall is load-bearing, Building Regulations approval is needed, with a structural engineer’s calculations for the steel beam and padstones. Where the beam bears on a shared wall, the Party Wall etc. Act 1996 applies.
Rules change and every property is different, so we check the planning history and constraints for your address before we quote.
What happens after you get in touch?
We look at the job
Book a visit and we'll come to you. The survey covers measurements, the state of what's there now and any obvious constraints, so the price that follows is based on your actual home, not an average.
Written quote
We put everything into a written, fixed-price quote: the specification, what's excluded, staged payments and the expected time on site. Take whatever time you need to decide; there's no pressure to commit.
Getting ready
Preparation matters as much as the build. We agree access, parking and working hours with you, order materials in good time, and confirm any permissions so the job isn't held up once it starts.
Build and hand over
Our trades complete removing a wall while your point of contact keeps you updated. When everything is finished, we clear the site, take away waste and go through the result with you before handover.
What you can expect from us
Questions about removing a wall in Kempston
Can I have a beam that does not show?
A flush or hidden beam sits within the depth of the ceiling so there is no visible downstand, giving a clean, open look. It is possible where the floor joists can be connected into the side of the beam, which takes more steel and labour. It costs more than a standard beam below the ceiling. The engineer confirms whether it suits your house.
Do I need building regulations approval to remove a wall?
Removing a load-bearing wall needs building regulations approval anywhere in the UK, and in Scotland a building warrant. A structural engineer calculates the beam and supports, and building control inspects the work. Removing a non-structural wall may still need approval if it affects fire escape routes, such as opening a hallway into a living room. We handle the applications and inspections.
Who do I deal with during the job?
One point of contact manages your project from survey to handover. They schedule the trades working under our contract, keep you updated on progress, and are the person to call with any question. You don't need to coordinate builders, electricians or decorators separately, because that is part of what we do.
Which postcodes in Kempston do you cover?
We cover MK42, along with the rest of Bedfordshire. If your postcode is not listed, get in touch anyway: our coverage is UK-wide, and we can usually arrange a survey wherever you live. Enter your postcode in the guide-price tool or contact form and we will confirm.
What is a steel beam and why is it needed?
A steel beam, often called an RSJ, is a strong steel section installed where a load-bearing wall used to be, so the weight above is carried across the opening to the walls at each end. It sits on padstones that spread the load. The size depends on the span and the load, which a structural engineer calculates. The beam is then boxed in or plastered.
Nearby towns
Live in Kempston? Our coverage takes in the MK42 postcode areas and reaches out to Bedford, Ampthill and Milton Keynes, so homes on the outskirts and in the next town along are included.