Wall removal is taking out an internal wall to open up rooms; where the wall is load-bearing, a steel beam sized by a structural engineer is installed on padstones to carry the weight above, with the work approved by building control.
For a homeowner in Kilburn, planning removing a wall tends to begin with two questions: what will it cost, and how disruptive will it be? Our guide range is £3,900–£10,500 including VAT, and a typical job runs to 1–3 weeks including making good. Both numbers firm up once we have seen the property, measured up and agreed exactly what is included.
- Guide price
- £3,900–£10,500 inc VAT
- Time on site
- 1–3 weeks including making good
- Postcodes
- NW2, NW3, NW6, NW8 and NW11
- Planning rules
- England
- Local area
- Greater London
- Survey
- Free, with a written quote
What should you budget for removing a wall in Kilburn?
What should you budget for removing a wall in Kilburn? Use the figures below as a starting point. Prices in London sit about 30% above the national guide, so the range here is £3,900–£10,500 including VAT. Your fixed price comes in writing once we've surveyed the property, at no charge.
| Type of job | What it usually involves | Guide in Kilburn |
|---|---|---|
| Non-load-bearing wall | Removing a stud or block partition and making good walls, ceiling and floor. | £1,050–£2,600 |
| Load-bearing wall up to 4m | A typical kitchen-diner knock-through with one steel beam, calculations and building control. | £3,900–£10,500 |
| Wide or complex opening | Openings over 4m, posts, flush beams or chimney breast removal. | £10,500–£21,000 |
The main things that change the figure:
- Opening width and the load the wall carries
- Beam size, posts, flush fixing and padstone details
- Services in the wall that need rerouting
- Engineer, building control and any party wall costs
What do you get?
- Survey to establish what the wall supports and where loads go
- Structural engineer's calculations and beam specification
- Building control application and inspections
- Temporary propping and dust protection during the work
- Steel beam installed on padstones and packed tight
- Plastering, flooring repairs and making good ready for decorating
Local housing and removing a wall
London's housing is dominated by Victorian and Edwardian terraces, often in yellow London stock brick, with Georgian terraces in central districts and mansion blocks across many inner areas. Outer boroughs have large belts of interwar semis, and there are extensive post-war council estates. Many houses have been split into flats, and conservation areas are widespread.
Terraces suit side-return extensions and rear dormer loft conversions; interwar semis commonly take hip-to-gable lofts. Shared party walls, restricted parking and conservation rules often shape the plans and the programme.
Knowing the typical building types in London helps, but a survey of your own home in Kilburn is what decides the right approach to removing a wall.
Do you need permission in Kilburn?
For anyone in Kilburn, the relevant framework is England's. The summary below is general, so we always contact the council about your address before putting a price in writing.
Removing an internal wall does not need planning permission in England unless the house is listed.
If the wall is load-bearing, Building Regulations approval is needed, with a structural engineer’s calculations for the steel beam and padstones. Where the beam bears on a shared wall, the Party Wall etc. Act 1996 applies.
Rules change and every property is different, so we check the planning history and constraints for your address before we quote.
The four stages
A visit to your home
We begin by looking at the job in person. During the free survey we discuss options, materials and budget for removing a wall, and photograph or measure anything the quote needs to reflect.
Quote in writing
We turn the survey notes into a written quote. The price is fixed for the specification we agree, and the document sets out materials, scope and payment stages in plain language.
Booking the work
Next comes planning the work itself. We set a start date that suits you, line up the right trades, and make sure any approvals for removing a wall are in place before the first day on site.
Build and hand over
Work goes ahead as scheduled and you deal with one contact throughout. When the last trade leaves, we clear and clean the site, talk you through what has been done and pass on any certificates and care instructions.
What you can expect from us
Common questions
Do I need building regulations approval to remove a wall?
Removing a load-bearing wall needs building regulations approval anywhere in the UK, and in Scotland a building warrant. A structural engineer calculates the beam and supports, and building control inspects the work. Removing a non-structural wall may still need approval if it affects fire escape routes, such as opening a hallway into a living room. We handle the applications and inspections.
Who do I deal with during the job?
One point of contact manages your project from survey to handover. They schedule the trades working under our contract, keep you updated on progress, and are the person to call with any question. You don't need to coordinate builders, electricians or decorators separately, because that is part of what we do.
Does the Party Wall Act apply to wall removal?
The Party Wall etc. Act 1996 applies in England and Wales only. Removing an internal wall usually does not involve it, but if the beam bears into a wall shared with a neighbour, as is common in terraced and semi-detached houses, you must serve notice first. Scotland and Northern Ireland have no equivalent Act. We tell you during the survey whether notices are needed.
Can you combine removing a wall with other work?
Yes. Because we manage several trades under one contract, we can plan removing a wall alongside other work on your Kilburn home, such as new windows with rendering, or a kitchen refit with an extension. Combining jobs can reduce repeat set-up such as scaffolding, skips and access, and every element is listed and priced in the same written quote.
What is a steel beam and why is it needed?
A steel beam, often called an RSJ, is a strong steel section installed where a load-bearing wall used to be, so the weight above is carried across the opening to the walls at each end. It sits on padstones that spread the load. The size depends on the span and the load, which a structural engineer calculates. The beam is then boxed in or plastered.
Nearby towns
We survey and quote throughout Kilburn's NW2, NW3, NW6 and NW8 postcodes and in surrounding places such as Cricklewood, Golders Green and Chalk Farm. The process and pricing approach are identical in each of them.